🏠 Trusted Local Roofers
Gutter Replacement & Installation Market Harborough
Old gutters give up slowly. A run that once carried rainwater cleanly starts to sag, drip and stain the wall below. When yours reach that point, gutter replacement in Market Harborough is a job worth doing once and doing right. Tate & Sons Roofing strips out tired guttering and installs new across the Harborough District.
This page is about the decision to replace. It covers when to swap a whole run and when a single section will do. It also shows how new gutters tie in with your fascias and roofline. You will also find real costs, timescales and the guarantee behind the work. It sits alongside the wider guttering services across Market Harborough we offer.
- Fully Insured
- 10-Year Guarantee
- 5-Star Rated
Quick Free Estimate - No Obligation
We're not just roofers – we're your neighbours.
Fully Insured • Response within 15 mins
🔒 Your details are safe with us. No spam, ever.
Know the Signs Your Gutters Have Reached the End
Gutters do not fail all at once. They give plenty of warning first. Spot the signs early and you replace on your terms, not after water has soaked the wall.
Look out for these:
- Cracks running along the length of the gutter, not just at a joint
- Sections sagging or pulling away from the fascia board
- Three or four joints leaking along the same run
- Rust patches and holes on old cast iron gutters
- Water spilling over the front edge in heavy rain
- Green streaks or damp staining down the wall below
- Plants or moss taking root in the gutter itself
One failed joint is a repair, not a new run. But cracks along the material itself tell a different story. When the plastic has gone brittle or the cast iron has rusted through, patching only buys a season. Most uPVC runs last 20 to 30 years before the material tires out. Reach that age and a full replacement usually costs less than yearly call-outs. We see this on older homes around Lubenham and Foxton, where a run has been patched three times over and still drips.
Whole Run or Just a Section — Which One Do You Actually Need?
Not every fault means the whole lot comes down. A single cracked length or one failed joint is often a quick section swap. Widespread sagging, brittle plastic or rust along the run points to replacing the full run instead.
The table below sets out the three routes we take, with real figures. It helps you see where your gutters sit before we survey.
| :-: | :-: | :-: | :-: |
| Option | Typical cost | When it makes sense | Notes |
| Replace a single section | £120–£350 | One cracked length or a failed joint, rest of the run sound | Quick fix; colour may not match a faded older run exactly |
| Replace a whole run | £450–£1,600 | Sagging, brittle plastic or joints leaking along the length | Priced per metre, roughly £30–£60 fitted; every outlet and downpipe renewed |
| Replace with a roofline upgrade | £2,000–£4,500+ | Fascia or soffit boards rotten behind the gutter | Gutters, fascias and soffits in one visit; one lot of access, one guarantee |
A section swap keeps costs down when the rest of the run is sound. The catch is colour. New uPVC sits bright next to a run that has faded for fifteen years. On a front elevation that shows, a whole run often looks better for not much more. We give you the honest call, not the biggest invoice. For a fuller look at systems and profiles, see our Guttering Installation and Replacement page.
Replace Gutters and Roofline Together and Save a Second Job
Your gutters bolt straight onto the fascia board. That link matters when the fascia behind them has started to rot. Once a board goes soft, brackets lose their grip and the run sags no matter how new the gutter is.
Doing both at once makes plain sense. The gutters have to come off to reach the fascia anyway. With the run down, we check the timber, fit new boards, then refit gutters at the correct fall. That fall is what stops future ponding and leaks. Split the jobs across two visits and you pay twice for access and twice for a crew.
We handle roofline work across Great Bowden and Little Bowden every week. If the survey shows sound fascias, we say so and leave them be. Where the timber has gone, our Fascias and Soffits work slots into the same visit. One scaffold or tower, one tidy-up, one guarantee across the whole roofline.
Seamless or Sectional — Matching the New Run to Your Home
Two build styles cover most new gutter runs. Sectional guttering uses set lengths joined with clips and seals. Seamless aluminium is rolled on site into one continuous length, with joins only at corners and outlets.
Each has its place:
Ryan Tate, our project manager, fits all three day in, day out. He will walk you through which one suits your home, your budget and how long you want it to last. No jargon, just a straight recommendation for your roofline.
- **Sectional uPVC*is quick to source, simple to fit and easy on the budget. It suits most homes and colours in well. Every joint is a seal that may need attention down the years.
- **Seamless aluminium*runs as one clean line along the roofline. With no joints along the length, there is far less to leak. It costs more to fit, since the run is formed on site with special kit.
- **Cast iron*stays right for period and listed homes where looks and heritage rules matter. It is heavier and slower to fit, so the price climbs.
What Gutter Replacement Costs in Market Harborough
Cost comes down to run length, material and access.
As a general guide, fitted uPVC runs roughly £30–£60 per metre. A full replacement on a standard three-bed semi lands around £800–£1,600. Seamless aluminium and cast iron sit higher, since the material and labour both cost more. Removing and tipping the old run adds around £6 per metre.
What moves a price up or down:
- **Run length*— more metres and more corners mean more labour and material
- **Access*— a two-storey rear reached only by scaffold adds roughly £250–£500
- **Material*— uPVC is cheapest, aluminium and cast iron cost more per metre
- **Fascia condition*— rotten board behind the run adds board replacement before gutters go back
- **Downpipes and outlets*— extra drops and hoppers add to the fittings count
These are market ranges, not a quote for your home. Two houses the same width can price apart once access and fascia condition come in. The only way to a firm figure is a proper look. Our free drone survey gives you that, then a clear written price with nothing added later. A fixed price needs a survey.
How Long the Job Takes and What Disruption to Expect
A gutter replacement is quicker than most homeowners fear. On a standard three-bed semi with sound fascias, a full uPVC run front and back is usually a one-day job. Larger homes, or a run that needs scaffold, may run to two days.
Here is the order we work in:
- Old gutters and downpipes taken down and cleared away
- Fascia line checked and any soft board flagged before we go on
- New brackets set to the correct fall for clean drainage
- New run, outlets and downpipes fitted and clipped home
- Every joint and drop tested with water before we leave
- Site cleared, old material tipped, driveway swept
Disruption stays low. The work happens outside, so you keep the run of your home. Cast iron takes longer than uPVC at every stage, since each length weighs far more. We give you a realistic timeframe before we start, not an easy promise to win the job. You will know who turns up and roughly how long they stay.
The Guarantee Behind Every New Gutter Run
A new run should last decades, so we stand behind ours in writing. You get a workmanship guarantee on the fit, on top of the manufacturer cover on the materials themselves. That means brackets at the right spacing, the correct fall, and joints that hold.
Getting the fall right is the part that matters most. Too flat and water sits and overflows; too steep and it races past the outlet. A gutter set to a proper slope, around 1 in 360 or steeper, drains clean every time. Want an independent read on roof drainage and how a run should perform? The Department for Communities technical note on roof drainage is worth a look before you commit.
Why Market Harborough Homeowners Call Tate & Sons First
You are not just buying a gutter run — you are buying whoever fits it. Ryan Tate, our project manager, took his NVQ Level 3 in Roofing and specialises in guttering and roofline. He handles the site work too. He is part of the same crew that turns up to fit your run, not just the man who quoted it.
Founder Michael Tate started his apprenticeship at sixteen and built Tate & Sons on one rule: fix the cause, not the symptom. He surveys every job himself. A sagging run gets traced back to the real fault, whether that is a tired bracket or a rotten board behind it. Between us we carry over 45 years of combined experience, hold NVQ Level 2 and 3 qualifications in Roofing Occupations, and keep CSCS cards and NFRC trade-body membership. Read more about the people behind the work on our About Tate & Sons Roofing page.
Areas We Serve Across Market Harborough and the Harborough District
We replace and install gutters across Market Harborough and the surrounding Welland Valley villages. If your area is not on the list below, call us anyway — if you are nearby, there is a strong chance we cover you.
- Market Harborough (LE16)
- Great Bowden (LE16 7)
- Little Bowden (LE16 8)
- Lubenham (LE16 9)
- Foxton (LE16 7)
- Medbourne (LE16 8)
- Kibworth Beauchamp (LE8)
- Great Glen (LE8 9)
- Fleckney (LE8 8)
- Husbands Bosworth (LE17 6)
- Desborough (NN14 2)
Got Questions?
Your Gutter Replacement Questions, Answered Properly
How do I know I need new gutters rather than a repair?
Repair works when the fault is isolated, like one cracked length or a single loose bracket. You need new gutters when the trouble is spread across the run. Cracks along the material, several leaking joints, sagging sections or rust holes all say the system is tiring out. Most uPVC runs last 20 to 30 years, so age is a fair guide too. If you are calling someone out every year, a full replacement usually costs less over time.
Should I replace the whole run or just the damaged section?
Swap a section when one length has failed and the rest is sound. It is quicker and cheaper for an isolated fault. Replace the whole run when sagging, brittle plastic or leaks show up along its length. Colour is the other factor — new uPVC sits bright next to a run faded by years of sun. On a front elevation that shows, a whole run often looks tidier for little extra.
How long does a gutter replacement take?
Most homes are a one-day job. A full uPVC run front and back on a standard three-bed semi is usually done in a day, provided the fascias are sound. Larger homes, or a run that needs scaffold, may take two days. Cast iron takes longer at every stage, since each length is far heavier than plastic. We give you a realistic timeframe before we start.
Should I replace fascias and soffits at the same time as the gutters?
If the boards behind your gutters have rotted, yes. The gutters have to come off to reach the fascia anyway. Doing both in one visit saves a second lot of access and labour. New boards also let us refit the run at the correct fall, which stops future leaks. Where the fascias are sound, we leave them and just renew the gutters. The survey tells us which case you are in.
What is the difference between seamless and sectional gutters?
Sectional gutters use set lengths joined with clips and seals along the run. Seamless aluminium is rolled on site into one continuous length, with joins only at corners and outlets. Fewer joints means far less to leak over the years. Seamless costs more to fit, since the run is formed on site with special kit. Sectional uPVC stays the cheaper, simpler choice for most homes.
How much does it cost to replace gutters in Market Harborough?
As a general guide, fitted uPVC runs roughly £30 to £60 per metre. A full replacement on a standard three-bed semi lands around £800 to £1,600. Aluminium and cast iron cost more per metre, and a two-storey rear may add £250 to £500 for scaffold. Rotten fascia behind the run adds board replacement on top. A free drone survey gives you an exact written price rather than a rough phone estimate.
Do you have to take the old gutters down to fit new fascia boards?
Yes. The gutters bolt onto the fascia, so they must come off before a new board goes on. That is exactly why replacing both together saves money. With the run down, we check the timber, fit the boards, then refit gutters at the right fall. Trying to work around gutters left in place makes the job slower and the finish worse.
What guarantee comes with a new gutter run?
You get a workmanship guarantee on our fit, plus the manufacturer cover on the materials. That means correct bracket spacing, the right fall, and joints that hold. We set the run to a proper slope so it drains clean rather than ponding and overflowing. If anything is not right, we come back and put it straight.
Book Your Free Drone Roofline Survey Today
See exactly what your gutters need before any work starts. No ladders, no pressure — just a clear picture from a local Market Harborough team.
Every week a tired gutter run waits, water works deeper into the wall and the fascia behind it. A quick, free survey today tells you exactly where you stand — and often the fix is smaller than you feared. Book now, get an honest quote, and protect your home before the next downpour finds the weak spot.
ð 5 Hood Close, Market Harborough, LE16 9XS
ð 01858 457600
Call the Market Harborough team today on 01858 457600, or request your free drone survey online. We're already working across your area.
Book Your Free Drone Roof Survey
See exactly where your roof stands, with no obligation and no pressure. Call our Market Harborough team or request your free drone survey today.
Get in Touch
Tate & Sons Roofing — Market Harborough Office
5 Hood Close, Market Harborough, LE16 9XS
📞 01858 457600
✉️ [email protected]